AG60 plasma cutting gun 4M-8M

AG60 plasma cutting gun is an air plasma cutting tool that focuses on universality and stability. Its 4M-8M specifications cover different operating radius requirements and are suitable for effect cutting of medium and thin plates. It is widely used in industrial production and maintenance scenarios. The following is its detailed product information:

1、 Core performance parameters

Rated current: The mainstream models have a rated current of 60A, and some high-end versions can reach 70A. The short-term peak current can reach 80A, suitable for medium and low load cutting needs;

Load duration rate: 60% (stable operation at rated current, meeting continuous operation requirements);

Cutting ability: With a large cutting thickness of 15-18mm, it has good cutting efficiency and low thermal deformation for metal plates such as carbon steel and stainless steel;

Gas parameters: working pressure 3-8 bar (recommended 4.5-5.0 bar for some models), gas flow rate 80-160 L/min, suitable for air as cutting medium, partially compatible with protective gases such as argon;

Cable length: 4M, 5M, 6M, 7M, 8M standard specifications, suitable for different operating radii (such as fixed workstations in workshops, outdoor repair scenarios, etc.), some reputation supports customization;

Weight: The 4M model weighs about 1.8-2.5kg, the 5M model weighs about 2.5kg, the 7M model weighs about 3.0kg, and the 8M model weighs about 3.2kg. The weight gradually increases with length, and the overall portability is good;

Ignition method: High frequency ignition (HF) or non-contact pilot arc, with fine arc initiation and less splashing, suitable for various board surfaces.

2、 Structure and core components

Cable configuration: Using a 6-square-meter copper core cable (some models are 14mm ²), with stable conductivity, low heat loss, and an outer layer wrapped in wear-resistant (based on actual reports) rubber or flame-retardant cloth, which is resistant to pulling and splashing, and extends the service life;

Gun head and key components:

Gun head material: Made of high-quality phenolic resin (bakelite) or copper, with good flame retardancy, high temperature resistance (based on actual reports), and excellent isolation and cutting effects against high temperatures and splashes;

Core consumables: equipped with pre installed consumables such as nozzles, electrodes, vortex rings, protective covers, etc., mostly made of copper alloy, wear-resistant (based on actual reports), high temperature resistant (based on actual reports), easy to replace, protecting cutting accuracy and stability;

Connection interface: The mainstream is M16 × 1.5 threaded air interface, paired with 2-pin or 5-pin plugs, suitable for most plasma cutting machines (such as CUT40, CUT50, CUT60, LGK60, etc.), with strong versatility;

Handle design: Ergonomic sliding handle, made of insulated plastic material, with good insulation effect, easy to operate for a long time without fatigue, integrated push switch, convenient arc control, easy for beginners to get started.

3、 Applicable scenarios and compatible devices

Applicable industries:

Industrial production: used for batch cutting and processing of medium and thin metal sheets in industries such as automobile manufacturing, engineering machinery, shipbuilding, chemical machinery, etc;

Maintenance and processing: Hardware accessory processing, equipment partial maintenance, on-site construction of steel structures, etc., suitable for various metal materials (carbon steel, stainless steel, aluminum alloy, etc.);

Equipment adaptation: Compatible with most 30-60A plasma cutting machines, including Rilon, Jasic, Chiry, Vector Welding, etc., with good reputation. The specific interface (thread specification, plug pin count) needs to be confirmed to match and avoid poor connection.

4、 Core advantages

Strong universality: compatible with most plasma cutting machines on the market, with standardized interfaces, easy replacement, and no need for additional modifications;

Exquisite effect: suitable cutting speed, smooth incision, small thermal deformation, better cutting quality for medium and thin sheets than traditional oxygen cutting, reducing subsequent polishing processes;

Good practicality: The core components are made of copper, high-quality plastic, wear-resistant (based on actual reports) rubber and other materials, which are wear-resistant, heat-resistant, have a long service life, and low maintenance costs;

Easy to operate: lightweight design+ergonomic handle, strong portability, suitable for handheld operation, high-frequency ignition technology reduces the difficulty of arc starting, and beginners can also get started at a suitable speed;